Tel: +86-13852691788   E-mail: sales@didinglift.com
Home » Blog » News » What Causes an Electric Pallet Stacker to Lose Lifting Power?

What Causes an Electric Pallet Stacker to Lose Lifting Power?

Views: 0     Author: Site Editor     Publish Time: 2026-11-21      Origin: Site

Inquire

Among the fault complaints for an Electric Pallet Stacker, "weak lifting" is one of the most frequent issues. Unlike a complete failure to lift that directly stops operations, it makes every stacking cycle slow and laborious—and over time accelerates wear on the hydraulic pump and motor. Taking Diding Lift's 2T Electric Walkie Pallet Stacker CDDA as an example, its Bucher hydraulic system and AC lifting motor form the core chain of the lifting action. Faults typically occur somewhere along the chain of "power output → pressure build-up → mechanical execution." This guide outlines causes and handling paths in order from easy to difficult.

2T Electric Walkie Pallet Stacker CDDA1.png

1. Check the "Oil" First: Hydraulic Oil and Filter Are the Most Basic Yet Overlooked Step

Industry maintenance experience repeatedly confirms one principle: for hydraulic troubleshooting, check the oil first, then the valves, and disassemble the pump last. A significant proportion of weak lifting issues can be traced to the oil circuit.

1.1 Insufficient Hydraulic Oil

When oil level is low, the pump draws in air and cannot build effective pressure, manifesting as noticeably slow lifting, sometimes accompanied by sharp or dull noise from the pump station. Check whether the tank level is within the scale range; top up with the specified hydraulic oil if low. Never repeatedly start the lift motor in a low-oil condition—this can cause permanent pump damage.

1.2 Degraded or Emulsified Hydraulic Oil

Darkened, cloudy, or milky oil indicates degradation or water ingress. Emulsified oil has significantly reduced lubricity, causing unstable system pressure and weak lifting. Completely replace the hydraulic oil and check cylinder seals for damage that may have allowed moisture ingress. In routine maintenance, hydraulic oil filters should be replaced every 500 hours or six months—do not wait for a warning light.

Weak Lifting Diagnosis Priority Card Diagram.png

1.3 Clogged Filter or Suction Line

A clogged filter increases suction resistance and reduces flow, manifesting as slow lifting. Some vehicle hoses may develop hidden damage or collapse after being run over by pallets, also restricting flow. Handling: Replace the filter (do not clean and reuse); check the suction line for collapsed sections or foreign matter blockage.

2. Then Check the "Valve": The Relief Valve Is the Highest-Frequency Fault Point for Weak Lifting

If the oil circuit is normal, the next focus is pressure control valves. Among them, the relief valve is one of the most frequently occurring components in "weak lifting" faults.

2.1 Low Relief Valve Pressure or Stuck Spool

The relief valve limits maximum system pressure to protect hydraulic components. When the spool is jammed by sludge or spring force weakens, the relief valve opens and relieves pressure before reaching rated pressure, preventing system pressure build-up. This manifests as possibly normal no-load operation but noticeable weakness under load, or complete failure to lift. Industry experience shows a typical pattern: normal no-load lifting, but slow or no lifting under full load—this is usually not a pump issue, but a low relief valve pressure setting or stuck spool.

Handling: Disassemble and inspect the relief valve, clean the spool and seat; replace the spring if failed; recalibrate pressure to the equipment's rated value. Non-professionals should not adjust pressure parameters arbitrarily.

2.2 Lowering Valve or Check Valve Jamming

In some cases, the lowering valve or check valve is in a partially closed state, preventing pressure from fully entering the cylinder. Try repeatedly operating the lowering button and observe for brief movement to determine whether the spool is jammed.

3. Then Check the "Seals": Internal Leakage Causes "Pressure That Won't Hold"

If oil and valves are normal but lifting remains weak, internal leakage in the hydraulic system should be suspected.

3.1 Cylinder Piston Seal Internal Leakage

After cylinder piston seals wear and age, high-pressure oil returns internally from the high-pressure chamber to the low-pressure chamber, and system pressure cannot be maintained. The typical manifestation is: slow lifting, and fork self-descent after stopping. Judgment method: raise forks to mid-position, stop operation, and observe whether descent exceeds 20mm within 10 minutes; if so, piston seal wear is likely. Handling: Disassemble the cylinder and replace seals.

3.2 Gear Pump Wear

After internal gear or pump body wear, increased clearance causes internal leakage—the pump barely works at no load but pressure drops rapidly under load. This is the "last component to consider" in weak lifting troubleshooting because replacement cost is higher. Only after all previous items are ruled out should gear pump wear be tested, with replacement if necessary.

4. Don't Forget "Electricity": Battery and Motor Also Affect Lifting Performance

Weak lifting is not always a hydraulic problem. The lifting power of an electric pallet stacker comes from the motor, and electrical abnormalities can also manifest as "no power."

4.1 Insufficient Battery Level or Aging

When battery level is insufficient, no-load voltage appears normal, but voltage drops instantly when the lift motor starts, reducing pump speed and flow, manifesting as slow or weak lifting. Battery capacity in older equipment degrades severely, especially under heavy-load conditions. Handling: Check the battery indicator and charge promptly; if the battery has been in service for over 3 years with severely reduced runtime, test capacity or replace.

4.2 Lift Motor or Contactor Issues

Burnt lift contactor contacts reduce current output and motor power. If the motor itself has carbon brush wear or loose wiring, output is similarly affected. The CDDA20's AC lift motor requires no carbon brush replacement, but contactors and wiring still require periodic inspection.

5. Finally Check "Mechanics": Excessive Resistance Also Makes Lifting Seem "Weak"

Sometimes the problem is not at the power end but at the execution end. Dust or lack of lubrication on fork chains, rollers, and rails increases mechanical resistance during lifting, appearing as "insufficient power" when it is actually "excessive friction". Handling: Clean chains and rails, apply lubricating grease; check mast carriage for jamming.

6. Conclusion and Action Recommendations

Troubleshooting weak lifting on an Electric Pallet Stacker should follow the sequence of "oil before valves, external before internal, simple before complex." In most cases, hydraulic oil level, filter condition, and relief valve jamming can explain a significant proportion of faults—rushing to replace the pump or motor is unnecessary. If forks are accompanied by self-descent, prioritize checking cylinder seal internal leakage.

Diding Lift has 12 years of experience and a 65,000 m² factory & workshop, with products complying with EN 12895:2015 and EN ISO 3691-1:2015 European standards, certified to ISO 9001:2015 quality management system and CE safety certification, and supports ODM/OEM cooperation & customization. Its 2T Electric Walkie Pallet Stacker CDDA is equipped with a Bucher hydraulic system and AC lifting motor, providing a design foundation for lifting reliability.

Inside the Diding Lift Factory.png

For CDDA20 hydraulic system parameters or troubleshooting guidance for specific faults, please send an email to sales@didinglift.com, and our professional team will provide one-on-one support.

References

  1. Hangcha. Common Maintenance Methods for Electric Pallet Trucks. i-ban.cn.

  2. Xin Niu Dun Forklift. Walkie Straddle Electric Pallet Stacker On-Site Troubleshooting and Maintenance Plan.

  3. Still. ECV 10 C Original Instructions Manual – Malfunction Analysis.

  4. Xin Niu Dun Forklift. Semi-Electric Stacker Common Fault Troubleshooting: Small Electric Forklift Repair Guide.

Product Inquire
Jiangsu Diding Machinery Co., Ltd.
Diding Lift is a professional Electric Pallet Truck, Electric Stacker, Reach Truck manufacturer supplier in China, specialized in providing customized competitive price. To buy or wholesale from our factory. For Quotation, contact us now.

QUICK LINKS

PRODUCT CATEGORY

CONTACT US
  Tel:  +86-13852691788
  
Tel: +86-523-87892000
 E-mail: sales@didinglift.com
                   info@didinglift.com
 Web: www.didinglift.com
 Address: No.1 East Road, Industrial Cluster Zone, Heshi Town, Taixing City, Jiangsu Province, China
Copyright ©  2024 Jiangsu Diding Machinery Co., Ltd. All rights reserved Sitemap